Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engines 2F and 3F-E
   - 3.2. The verhneklapannyj engine 1FZ-FE
      3.2.1. Technical characteristics
      3.2.2. Kinds of repair without engine dismantle
      3.2.3. A cover of a head of cylinders
      3.2.4. A soaking up collector
      3.2.5. A final collector
      3.2.6. Cam-shafts and pushers
      3.2.7. A head of cylinders
      3.2.8. A cover of a chain drive of cam-shafts
      3.2.9. A forward epiploon коленвала
      3.2.10. The oil pallet
      3.2.11. The oil pump
      3.2.12. A flywheel (a leading disk of the hydrotransformer)
      3.2.13. A back epiploon коленвала
      3.2.14. Suspension bracket and engine details
   + 3.3. Dismantle and engine major repairs
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


ссылка на кракен официальная в тор vk2 at зеркало

3.2.8. A cover of a chain drive of cam-shafts
THE GENERAL DATA

Details of a forward part of the engine

1. The compressor
2. An arm
3. The pallet 1
4. The gauge of level of oil
5, 7. Linings
6. The pallet 2
8. The bottom guard
9. A roller натяжителя
10. A pulley
11. An adjusting lath of a belt
12. A ring
13. A forward epiploon
14. A radiator branch pipe
15. A cover
16. Успокоитель
17. A gear wheel of a drive of the oil pump
18. A leading asterisk
19. A drive gear wheel
20. An oil atomizer
21. A boot натяжителя
22. A chain
23. A conducted gear wheel of a cam-shaft

Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Block back wheels.
3. Lift car redock.
4. Remove the bottom guards.
5. Remove a broad tank of a radiator (subsection 4.5 see).
6. Turn out candles and remove all belts of a drive.

7. Remove the compressor of the conditioner and take aside, without disconnecting from a highway (bolts of the compressor of the conditioner are specified by arrows).
8. Remove the generator, a roller натяжителя and all arms (bolts of an adjusting arm of the generator are specified by arrows).
9. Remove a cruise-control drive (if it is provided) and take aside.
10. Disconnect the bottom hose of a radiator and remove the pump of a cooling liquid.
11. Establish the piston of 1st cylinder in ВМТ a compression step.
12. Remove a head of cylinders.
13. Remove the pallet.
14. Turn away a bolt having fixed a pulley коленвала.
15. Cнимите a pulley коленвала a stripper.
16. Turn away bolts and nuts of a cover of a chain and cautiously uncover.
17. Remove a chain and an asterisk. Remove успокоители and details натяжителя.

Check

PERFORMANCE ORDER
1. Check up a condition of teeths of a gear wheel of a cam-shaft. Check up a chain condition, deterioration of rollers and connecting links. The worn out details replace. In case of strong deterioration успокоителей remove and clear the pallet and маслоприемник.
2. Check up work плунжера and a clamp натяжителя. Плунжер should move freely in a case aperture (at the left). The clamp should keep reliably плунжер (on the right).
3. Check up cleanliness of a jet of an oil atomizer.

Installation

Designation of bolts of fastening of a cover of a chain different by the sizes

Bolt And – 30 mm

Bolt In – 50 mm

Bolt With – 60 mm


PERFORMANCE ORDER

1. Clear a forward part of the engine, a chain and a cover, establish new sealing rings and an atomizer. The atomizer should be turned towards a chain.
2. Dress a chain on a cam-shaft asterisk, having combined labels, press out a chain with успокоителями, having tied up a strong tape.
3. Combine other link with a distinctive label with a groove under шпонку коленвала (arrows) and dress on a leading asterisk.
4. Put on a cover of 3 mm – the hermetic platen, be convinced available all linings and establish a cover (during no more than 5 mines after drawing), having entered the platen of a leading rotor of the oil pump into gearing with a leading gear wheel коленвала.
5. Wrap bolts (fig. the Designation of bolts of fastening of a cover of a chain different by the sizes see) and tighten with the set moment. Remove обвязку chains.
6. Establish other details upside-down. The engine start, only after check of correctness of installation of a chain.