Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
- 10. A body
10.1. Maintenance service and repair
10.2. Vinyl furnish
10.3. An upholstery and rugs
10.4. Repair of insignificant damages
10.5. Repair of considerable damages
10.6. Loops and locks
10.7. A windscreen and motionless glasses
10.8. A cowl
10.9. A latch of a cowl and a drive cable
10.10. A forward lattice
10.11. A forward wing
10.12. The internal panel of a door
10.13. The door lock, the lock and handle switch
10.14. Door glass
10.15. Window Lifter
10.16. Lateral mirrors
10.17. A door
10.18. A door of a back compartment
10.19. A back cover (the top door of a back compartment)
10.20. A casing of a steering column
10.21. Panels of forward facing of salon
10.22. Average floor section
10.23. The forward facing panel of salon
10.24. Seats
10.25. Bumpers
+ 11. An electric equipment
+ 12. Electroschemes
|
The prevention Works are carried out together.
Removal and installation
| PERFORMANCE ORDER |
| 1. Lift glass. Disconnect the battery from weight. |
| 2. Open a door and establish under a door wooden props, having covered their rags. |
| 3. Remove the internal panel of a door and a water filter. |
| 4. Disconnect all sockets of conducting, a wire on weight and latches, крепящие conducting plaits. Preliminary designate all sockets and wires. |
| 5. Disconnect a rubber casing from outside doors. Then stretch conducting through an aperture in a casing, having removed thereby from a door. |
|
6. Cautiously beat out an axis of the terminator of opening of a door in the direction specified by an arrow. |
| 7. Outline contours of door loops. |
|
8. Keeping a door, turn away bolts of loops using a special key for отворачивания bolts of door loops and remove a door. |
| 9. Installation is carried out upside-down. |
|
Adjustment
Adjustment of position of a clamp of the lock
|
|
For adjustment lower screws and move a lock clamp in the necessary direction. |
| PERFORMANCE ORDER |
| 1. Before adjustment check up presence люфта in axes of door loops. Completely open a door and shake a door upwards-downwards, without shaking thus a body. If люфт loops exceeds 1,6 mm it is necessary to replace loops. |
| 2. Adjustment of a door concerning a body is reached by door moving at the released bolts of fastening of loops to a body or to a door. Doors are considered adjusted if the top edge of a door is parallel to an edge of a roof of a body, the surface of a forward door settles down заподлицо with a wing, a surface of a back door – заподлицо with a back wing, and the bottom edges of doors coincide with a profile порожка. If adjustment of doors is not reached by moving to loops between loops and a body (door) it is necessary to lay remote linings (are available on sale). |
| 3. Remove the internal panel of a door and a water filter. |
| 4. For adjustment of position of the closed door outline a contour of a clamp and be convinced that the lock latch makes contact with the central part of a clamp. Otherwise adjust, moving a clamp upwards-downwards. |
| 5. For clamp adjustment of a lateral direction be convinced that the door is заподлицо with the next panels of a body (a forward or back wing). Otherwise move a clamp in a horizontal direction so that the door was заподлицо with the next panels of a body and was freely locked. |
|
|
|