Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engines 2F and 3F-E
   + 3.2. The verhneklapannyj engine 1FZ-FE
   - 3.3. Dismantle and engine major repairs
      3.3.1. Technical characteristics
      3.3.2. Diagnostics of the engine with the help вакууметра
      3.3.3. Compression check
      3.3.4. Dismantle of the power unit
      3.3.5. Removal and engine installation
      3.3.6. Alternatives of major repairs
      - 3.3.7. An order of dismantling of the engine
         3.3.7.1. A head of cylinders
         3.3.7.2. Repair of valves
         3.3.7.3. Shatunno-piston group
         3.3.7.4. Коленвал
         3.3.7.5. Clearing and check of the block of cylinders
         3.3.7.6. Хоннингование cylinders
         3.3.7.7. Rods and pistons
         3.3.7.8. Radical and шатунные bearings
      + 3.3.8. An engine assembly order
      3.3.9. Start-up of the engine after repair and обкатка
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


3.3.7.8. Radical and шатунные bearings
THE GENERAL DATA

Radical and шатунные bearings at engine major repairs are subject to the obligatory replacement, however the bearings which were in operation should be checked up carefully to restore the general condition of the engine at the moment of repair.

Sources of rupture of bearings of a cranked shaft are insufficient greasing because of wrong assemblage, pollution and penetration of extraneous particles, frequent overloads of the engine, corrosion, etc. Irrespective of the reason which have caused destruction of bearings, it should be eliminated.

Kinds of deterioration radical and шатунных bearings

Selection of radical bearings

The diagramme for selection шатунных bearings on engines 3F-E

 

Marks And
1,484 – 1,488 mm
Marks In
1,488 – 1,492 mm
Marks With
1,492 – 1,496 mm

The diagramme for selection шатунных bearings коленвала on engines 3F-E

1. Коленвал

2. The central counterbalance

3. Bearing N3

4. Dimensional group of the bearing

Marks on the bearing
Number on коленвале
3
4
5
Number on the block of cylinders
6
7
8
6
7
8
6
7
8
Dimensional group подшипника*
Т3
Т4
Т5
Т2
Т3
Т4
Т1
Т2
Т3

* Example: Number on коленвале 5, number on the block of cylinders 7 = dimensional group T2.

Diameter of radical bearings and internal diameter of an aperture under radical bearings on engines 3F-E

Diameter of a neck коленвала
Mm
Маркировка-3
N1
66.972 – 66.980
N2
68.472 – 68.480

N3

69.972 – 69.980
N4
71.472 – 71.480

Маркировка-4

 

N1
66.980 – 66.988
N2
68.480 – 68.488
N3
69.980 – 69.988
N4
71.480 – 71.488

Маркировка-5

 

N1
66.988 – 66.996
N2
68.488 – 68.496
N3
69.988 – 69.996
N4
71.488 – 71.496
Diameter of an aperture under radical bearings
N
Mm

Маркировка-6

 

N1
72.010 – 72.018
N2
73.510 – 73.518
N3
75.010 – 72.018
N4
76.510 – 76.518

Маркировка-7

 

N1
72.018 – 72.026
N2
73.518 – 73.546
N3
75.018 – 75.026
N4
76.518 – 76.526

Маркировка-8

 

N1
72.026 – 72.034
N2
73.526 – 73.534
N3
75.026 – 75.034
N4
76.526 – 76.524

The diagramme for selection standard шатунных bearings on engines 1FZ-FE

 

Put number
Marks on a rod
1
2
3
Number on коленвале
1
2
3
1
2
3
1
2
3
Marks of dimensional group подшипника*
2
3
4
3
4
5
4
5
6

* Example: Number on a rod 3 + number on коленвале 1 = Dimensional group of the bearing 4.

The diagramme for selection of standard radical bearings коленвала on engines 1FZ-FE


Put number
Marks on the block of cylinders
1
2
3
Number on коленвале 1 2 3 1 2 3 1 2 3
Marks of dimensional group подшипника* 2 3 4 3 4 5 4 5 6

*Example: Number on the block of cylinders 2 + number on коленвале 1 = Dimensional group of the bearing 3.

Diameter of radical bearings and internal diameter of an aperture under radical bearings on engines 1FZ-FE

Diameter of an aperture under radical bearings:

  – Marks 1

74.026 – 74.032 mm
  – Marks 2
74.032 – 74.038 mm
  – Marks 3
74.03 – 74.044 mm
Diameter of a neck коленвала:

  – Marks 1

68.994 – 69.000 mm
  – Marks 2
68.988 – 68.994 mm
  – Marks 3
68.982 – 68.988 mm
Thickness of standard bearings:

  – Marks 2

2.489 – 2.492 mm
  – Marks 3
2.49 – 2.495 mm
  – Marks 4
2.495 – 2.498 mm
  – Marks 5
2.498 – 2.501 mm
  – Marks 6
2.501 – 2.504 mm

PERFORMANCE ORDER
1. If bearings of standard dimensional groups the new bearing steals up under numbers put on replaced, and also under numbers on the block of cylinders and коленвале with use of tables are established.
2. If коленвал it was ground, bearings should be selected in car-care centre in which polishing was carried out.
3. After selection of bearings measure a backlash in necks (subsection 3.3.8.2 see).
4. Industrially at engine assemblage bearings with different colour marks which are put on an edge of the loose leaf of the bearing are established.
5. Marks of dimensional group of bearings are usually put from outside the loose leaf, turned to a back part коленвала, except for the back radical loose leaf which is marked from outside turned to a forward part коленвала.
6. It is supposed to establish the top and bottom loose leaves from various dimensional groups. For example, to correct a backlash on 0,0125 mm the standard loose leaf sometimes it is used with the loose leaf from group with the reduced diameter on 0,025 mm.

The prevention

It is forbidden to establish pair of loose leaves if distinction of their diameters exceeds 0,025 mm. On the size it is necessary to establish different loose leaves either all from above, or all from below.