Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
- 9. Suspension brackets and a steering
   9.1. Technical characteristics
   9.2. The stabilizer of a forward suspension bracket and the plug
   9.3. Forward and back shock-absorbers
   9.4. Springs and plugs
   9.5. Springs of suspension brackets (а/м FJ80)
   9.6. A cross-section bar (а/м FJ80)
   9.7. Suspension bracket levers (а/м FJ80)
   9.8. A rotary fist
   9.9. A steering wheel
   9.10. Steering draughts
   9.11. A reducer
   9.12. The hydraulic booster pump
   9.13. Removal of air from the wheel hydraulic booster
   9.14. Wheels and tyres
   9.15. Corners of installation of forward wheels
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


9.10. Steering draughts
THE GENERAL DATA

Details of the steering mechanism of cars FJ60, 62

1. Гаситель fluctuations
2. Шплинт
3. Сошка
4, 19. A tip of leading draught
5. A cover
6. Заглушка
7. A spring
8. A sharovyj finger of a tip of draught
9. Шплинт
10. A tip of leading draught
11. A saddle
12. Loose leaves of a spherical finger
13. A butterdish
14. From outside сошки
15, 18. A tip of conducted draught
16. From outside conducted draught
17. Conducted draught
20. The lever of a rotary fist

Details of the steering mechanism of cars FJ80

1, 4, 6, 10. A tip of leading draught
2. Draught
3. A collar
5. Сошка
7. Гаситель fluctuations
8. An arm
9. Leading draught
11. Шплинт

Check

PERFORMANCE ORDER
1. Turn of wheels is provided with transfer of effort from a wheel reducer through сошку, steering draughts and tips of draughts. In parallel сошке a wheel it is attached гаситель steering wheel fluctuations.
2. Expose wheels in driving position on a straight line and block a steering wheel.
3. Lift the car so that the wheel has appeared approximately in 2,5 sm from the earth.
4. Check up люфт in tips of draughts. For this purpose establish the indicator so that its leg rested against wheel edge. Slightly shake a wheel in a horizontal plane. If the indicator indication exceeds 6 mm it is necessary to check up a condition of all tips of draughts and to replace the worn out details.
5. Lift redock of the car and check up a condition of covers of tips of draughts and steering draughts, and also заедающих шарнирных connections.

Removal and installation

TIPS OF CONDUCTED DRAUGHT

PERFORMANCE ORDER
1. Remove a wheel.
2. Расpinуйте also release castellated a nut of the spherical hinge, a nut completely not to turn on.
3. A stripper выпрессуйте a finger of the hinge from an eye of the lever of a rotary fist.
4. At tip replacement count number of threads of a carving (it is specified by an arrow) on which will turn a tip. Release a collar and turn out a tip.
5. Grease a carving part of a tip консистентной with greasing and turn in draught so that the tip end face has defended from draught on number of threads of the carving, defined before removal. A collar not to tighten.
6. Insert a finger into an eye of the lever and wrap a nut. The finger should come into an eye densely. If the finger rotates in a lever eye at a nut tightening press it in конусное an aperture.
7. Replace pin, if necessary tighten a nut before coincidence of a groove of a nut to an aperture under pin in a carving part of a finger.

The prevention

It is forbidden to turn on a nut to provide free passage pinа.


8. Tighten nuts of collars.
9. Establish a wheel and lower the car.

LEADING DRAUGHT

PERFORMANCE ORDER
1. Lift one party of the car.
2. Disconnect from leading draught гаситель fluctuations (subitem 2 and 3 see).
3. Disconnect draught from сошки a shaft of a reducer, a rotary fist (or conducted draught on cars FJ 60,62), having executed actions on subitem 2 and 3.
4. If necessary replace tips, having executed corresponding actions on change of tips of conducted draught.
5. Assemblage is carried out upside-down. Tighten all fastenings with the set moment.

СОШКА

PERFORMANCE ORDER
1. Disconnect leading draught.
2. Will release a nut сошки. Designate position сошки concerning a reducer shaft.
3. Remove сошку.
4. Turn away a nut and remove сошку.
5. Assemblage is carried out upside-down. Combine the labels put at dismantling.

ГАСИТЕЛЬ FLUCTUATIONS

PERFORMANCE ORDER
1. Disconnect гаситель fluctuations, having executed actions under item 2.
2. Turn away a nut (it is specified by an arrow) fastenings to a frame and remove гаситель fluctuations.
3. Installation is carried out upside-down. Tighten nuts with the set moment.