Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of cooling, heating
- 5. Fuel and exhaust systems
   + 5.1. Carburettor engines
   - 5.2. Engines with fuel injection
      5.2.1. Technical characteristics
      5.2.2. Декомпрессия fuel system
      + 5.2.3. The fuel pump and pressure of fuel
      5.2.4. Gasoline pipe lines and joints
      5.2.5. The fuel pump
      5.2.6. The gauge of level of fuel
      5.2.7. The air filter
      5.2.8. A cable of a drive throttle заслонки
      - 5.2.9. System of electronic injection of fuel (EFI-system)
         5.2.9.1. Check of system of electronic injection of fuel
         - 5.2.9.2. Units of system of electronic injection of fuel
            5.2.9.2.1. The case throttle заслонки
            5.2.9.2.2. The gauge of an angle of rotation throttle заслонки
            5.2.9.2.3. A regulator of pressure of fuel
            5.2.9.2.4. The valve of a regulator of turns of idling
            5.2.9.2.5. The fuel and atomizer distributor
            5.2.9.2.6. The levelling chamber
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


5.2.9.2.2. The gauge of an angle of rotation throttle заслонки
THE GENERAL DATA

The table of check of the gauge of turn throttle заслонки (1988-92)

Backlash between the lever and the screw throttle заслонки
Steams of conclusions
Resistance
0 mm
VTA-E2
0,3 – 6,3 clod
0,50 mm
IDL-V2
<2,3 clod
0,75 mm
IDL-V2
Infinity
Заслонка it is completely open
VTA-E2
3,5 – 10,3 clod
VC-E2
4,52 – 8,25 clod

The table of check of the gauge of turn throttle заслонки (since 1983)

Backlash between the lever and the screw throttle заслонки
Steams of conclusions
Resistance
0 mm
VTA-E2
0,2 – 5,7 clod
0,50 mm
IDL-V2
<2,3 clod
0,75 mm
IDL-V2
Infinity
Заслонка it is completely open
VTA-E2
2,0 – 10,2 clod
VC-E2
2,5 – 5,9 clod

Check

PERFORMANCE ORDER
1. Disconnect from the gauge a socket.
2. Between the restrictive screw throttle заслонки and the lever lay щуп the set thickness (1 – the lever, 2 – the terminator, 3 – a making place щупа).
3. Measure resistance between steams of conclusions specified in corresponding tables, laying щупы a various thickness (1 – an ohmmeter, 2 – depression, 3 – щуп).
4. If the measured resistance differs from specified in the table between the lever and the screw заслонки lay щуп in the thickness of 0,93 mm (on cars 1988-92) or 0,62 mm (on cars since 1993) and connect an ohmmeter to conclusions IDL and Е2. Release screws of fastening of the gauge and slowly turn the gauge clockwise until then while the ohmmeter will not show rupture.
5. Tighten screws and with the help щупов the set thickness again check up resistance between the specified conclusions.
6. If adjustment does not possible to achieve the set resistance remove the gauge and replace, then adjust.