Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of cooling, heating
- 5. Fuel and exhaust systems
   + 5.1. Carburettor engines
   - 5.2. Engines with fuel injection
      5.2.1. Technical characteristics
      5.2.2. Декомпрессия fuel system
      + 5.2.3. The fuel pump and pressure of fuel
      5.2.4. Gasoline pipe lines and joints
      5.2.5. The fuel pump
      5.2.6. The gauge of level of fuel
      5.2.7. The air filter
      5.2.8. A cable of a drive throttle заслонки
      - 5.2.9. System of electronic injection of fuel (EFI-system)
         5.2.9.1. Check of system of electronic injection of fuel
         - 5.2.9.2. Units of system of electronic injection of fuel
            5.2.9.2.1. The case throttle заслонки
            5.2.9.2.2. The gauge of an angle of rotation throttle заслонки
            5.2.9.2.3. A regulator of pressure of fuel
            5.2.9.2.4. The valve of a regulator of turns of idling
            5.2.9.2.5. The fuel and atomizer distributor
            5.2.9.2.6. The levelling chamber
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


5.2.9.2.5. The fuel and atomizer distributor Check

Execute checks of system of injection (subsection 5.2.9.1 see).

Replacement

PERFORMANCE ORDER
1. Execute декомпрессию.
2. Disconnect the battery from weight.
3. Disconnect from a head of cylinders and a soaking up collector a ventilation hose картера.
4. Remove the levelling chamber (subsection 5.2.9.2.6 see).
5. Put accurately distinguishable labels on each socket of an atomizer. Disconnect sockets from atomizers and take conducting aside.
6. Disconnect from the fuel distributor a vacuum hose.
7. Disconnect from a pressure and distributor regulator fuel hoses.
8. Turn away bolts of fastening of the distributor of fuel (are specified by arrows).
9. Remove the distributor of fuel with atomizers.
10. Get from the distributor of an atomizer and put in a box with an individual label.
11. If atomizers do not vary, replace rings and уплотнители. Remove from an atomizer a ring.
12. Remove уплотнители and get rings from apertures in an inlet collector.
13. Atomizers are established upside-down.
14. Tighten bolts of fastening of the distributor of fuel with the set moment.

STARTING ATOMIZER (1988-92)

Check

PERFORMANCE ORDER
1. Disconnect a socket.
2. Check up resistance between conclusions and compare to the standard.
3. If resistance corresponds to norm the atomizer is serviceable, check up serviceability of the relay of an atomizer.
4. If resistance differs from norm an atomizer replace.
5. Attach a socket.

Removal

PERFORMANCE ORDER
1. Execute декомпрессию and disconnect the battery from weight.
2. Disconnect an atomizer socket.

3. Substitute the pallet and turn away the union.

4. Turn away a nut and remove an atomizer with a lining.
5. Check up an atomizer torch at the stand (it is carried out in car-care centre).
6. Establish an atomizer upside-down.

THE RELAY OF THE STARTING ATOMIZER (1988-92)

Check

PERFORMANCE ORDER
1. Check up resistance of the relay (is near to the thermostat).
2. At temperature more low 15 About resistance should be 30–50 Ohm.
3. Warm up the engine. At temperature above 30 About resistance should be 70–90 Ohm.
4. Resistance between conclusion STA (with it is black / a red wire) should be 30–90 Ohm.

Replacement

PERFORMANCE ORDER
1. Merge a liquid.
2. Turn out the relay a tubular face key.
3. Installation is carried out upside-down.