Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engines 2F and 3F-E
   - 3.2. The verhneklapannyj engine 1FZ-FE
      3.2.1. Technical characteristics
      3.2.2. Kinds of repair without engine dismantle
      3.2.3. A cover of a head of cylinders
      3.2.4. A soaking up collector
      3.2.5. A final collector
      3.2.6. Cam-shafts and pushers
      3.2.7. A head of cylinders
      3.2.8. A cover of a chain drive of cam-shafts
      3.2.9. A forward epiploon коленвала
      3.2.10. The oil pallet
      3.2.11. The oil pump
      3.2.12. A flywheel (a leading disk of the hydrotransformer)
      3.2.13. A back epiploon коленвала
      3.2.14. Suspension bracket and engine details
   + 3.3. Dismantle and engine major repairs
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


3.2.10. The oil pallet Removal

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Put the car on a manual brake and block back wheels.
3. Lift car redock.
4. Remove mud guards of the engine.
5. Merge oil and remove the oil filter. Remove маслоуказатель.
6. Remove the stabilizer of a forward suspension bracket (subsection 9.2 see).
7. Remove exhaust pipes in gathering.
8. Remove the gauge of level of oil and examine.
9. Turn away bolts of the pallet 2 (the bottom section).
10. Cautiously separate and remove the bottom section.
11. Turn away bolts (are specified by arrows in a photo at the left) and nuts near to a pulley (are specified by arrows in a photo on the right) the pallet 1 (the top section).
12. Open consolidation and cautiously separate the top section.
13. Incline and remove the top section.
14. Turn away a fastening nut маслоприемника (are specified by arrows).
15. Turn away a nut маслоотражателей (are specified by arrows) and remove маслоприемник.

Installation

PERFORMANCE ORDER
1. Remove from demountable planes of the block of cylinders and the pallet the consolidation rests. Wash out condensed planes solvent.
2. Be convinced of cleanliness of carving apertures in the block of cylinders.
3. Check up presence on a demountable plane of the pallet of deformations, especially about apertures under bolts. If necessary отрихтуйте a plane a hammer on a board.
4. Check up a condition маслоприемника, presence on it of cracks and a contamination of the filter of rough clearing. Establish a tube маслоприемника.
5. Check up a condition of the gauge of level of oil and a socket. Replace a lining.
6. At assemblage establish a new lining маслоприемника in a forward cover.
7. Put 3 mm-platen of hermetic on a condensed plane of the pallet 1.

The prevention

The detail should be established not later than 5 minutes after hermetic drawing.


8. Cautiously establish the pallet and wrap bolts. In three-four receptions tighten bolts of the pallet with the set moment, beginning an inhaling in the central part.
9. Put 3 mm-platen of hermetic on a plane of the pallet 2, establish the pallet, in regular intervals and gradually tighten bolts with the set moment.
10. Further assemblage are carried out upside-down. Fill in oil in the engine and replace the filter. Replace linings of an exhaust pipe of the muffler.
11. Start the engine and be convinced of absence of a leak.