Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   - 3.1. Engines 2F and 3F-E
      3.1.1. Technical characteristics
      3.1.2. Kinds of repair without engine dismantle
      3.1.3. Installation of the piston of 1st cylinder in ВМТ
      3.1.4. A cover of a head of cylinders
      3.1.5. A lateral cover of the mechanism timing
      3.1.6. Коромысла and bars of pushers
      3.1.7. Springs of valves, plates, маслосъемные caps
      3.1.8. Soaking up and final collectors
      3.1.9. A head of cylinders
      3.1.10. Pushers
      3.1.11. A pulley коленвала
      3.1.12. A forward epiploon коленвала
      3.1.13. A forward cover
      3.1.14. A cam-shaft and drive gear wheels
      3.1.15. A cam-shaft and support
      3.1.16. Replacement of bearings
      3.1.17. The oil pallet
      3.1.18. The oil pump
      3.1.19. A flywheel (a leading disk of the hydrotransformer)
      3.1.20. A back epiploon коленвала
      3.1.21. Suspension bracket and engine details
   + 3.2. The verhneklapannyj engine 1FZ-FE
   + 3.3. Dismantle and engine major repairs
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


3.1.3. Installation of the piston of 1st cylinder in ВМТ
THE GENERAL DATA

The prevention

It is meant that works are carried out at correct installation of the distributor of ignition (if the distributor is provided).

If it is necessary to redeem correct position of the distributor define an engine step on sensation of a compression in 1st cylinder at the turned out candle then combine labels of the moment of ignition (see more low).

The installation order is identical to engines 2F, 3F-E and двухвальных верхнеклапанных 1FZ-FE.


PERFORMANCE ORDER
1. Installation of the piston of 1st cylinder in ВМТ a compression step is necessary for performance adjusting and наладочных works (adjustment of valves, installation of the moment of ignition, etc.).
2. Translate the transmission selector in position Neutral or Park (on automatic transmission) or in neutral position (on a manual transmission). Get the central high-voltage wire of the distributor of ignition and connect to weight.
3. Коленвал it is turned by a key for a head of a bolt of a pulley clockwise.
4. On a wire from a candle of 1st cylinder find a corresponding conclusion to a cover of the distributor of ignition and designate риской on the case. Uncover the distributor.

5. Turn коленвал a key for a head of a bolt of a pulley clockwise before combination risks on a flywheel (a leading disk of the hydrotransformer) with the index (on engines 2F and 3F-E, a photo at the left) or dredging on a pulley коленвала with a label "0" on a motionless scale (on engines 1FZ-FE, a photo on the right).
6. If the index бегунка the distributor is opposite risks on the distributor case the piston of 1st cylinder is in ВМТ a compression step. If бегунок it is turned on 180 from risks turn коленвал on 1 turn then the piston of 1st cylinder will be exposed in ВМТ a compression step. Thus labels on a scale and a pulley should be combined, and the index бегунка should be opposite the risks, 1st cylinder designating a conclusion.

The prevention

If to expose the piston of 1st cylinder is in ВМТ a compression step thus it is not possible, the reasons are wrong installation of the distributor of ignition, gear wheels or a chain of a drive of a cam-shaft.


7. Designate conclusions of other wires according to an engine operating procedure. Turning коленвал further clockwise concerning position ВМТ of 1st cylinder, it is possible to expose in ВМТ the piston of each cylinder, combining бегунок with labels of conclusions.