Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
- 2. Maintenance service
   2.1. Additional maintenance service
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance service terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tyres and pressure in tyres
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydrodrive of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Exhaust system check
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a distributing box
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. The thermostat of the air filter (carburettor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. System of catching of steams of gasoline
   2.24. System check рециркуляции
   2.25. Air заслонка the carburettor
   2.26. A zolotnik of system of ventilation картера
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of backlashes of valves
   2.30. Idling turns (carburettor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, бегунок and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a distributing box
   2.43. Oil replacement in a back (forward) reducer
   2.44. Backlashes in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


2.28. Replacement of spark plugs
THE GENERAL DATA

The complete set of tools for replacement of spark plugs

1. A candle face key
2. A Dinamometrichesky key
3. A rattle
4. An adapter
5. A set of calibres for backlash check between candle electrodes

Adjustment

PERFORMANCE ORDER
1. Prepare tools and adaptations. At replacement свеч it is necessary to get new candles of recommended type, to expose a backlash and to screw instead of old, replacing each candle separately.
2. Check up a condition of new candles. At detection of any signs of damages of an insulator it is impossible to establish a candle.
3. Check up a backlash between electrodes of new candles in calibre of round section. The backlash between electrodes should correspond specified in подкапотной to the tablet.
4. If the backlash does not correspond to norm turn in an electrode by means of the lever on the case of a set of calibres.
5. If the lateral electrode does not coincide with central turn in the lever on the case of a set of calibres before combination of both electrodes on the candle centre.

Removal
PERFORMANCE ORDER
1. On the engine 1FZ-FE for access to candles remove an overlay (a photo at the left). Turn a tip on a half-turn, simultaneously making the effort directed upwards, and get a wire (a photo on the right).
2. Blow the pump of a place round a candle, having removed a dirt.
3. Turn out a candle a key with the extension piece.
4. Irrespective of, whether the candle will vary, or to be wrapped old, check up a candle condition.

Installation

PERFORMANCE ORDER
1. Before заворачиванием candles into place it is recommended to grease a carving with structure against прихвата.
2. To wrap a candle without warps dress on a candle a piece of a hose with internal diameter 9,5 mm. As soon as the candle will start to be wrapped with a warp, the hose will start to be scrolled on an insulator owing to what carving damage is prevented.
3. Tighten a candle with the set moment.
4. Establish a tip, having turned on a half-turn and simultaneously having made the effort directed downwards.
5. In a similar order replace other candles.