Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
- 2. Maintenance service
   2.1. Additional maintenance service
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance service terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tyres and pressure in tyres
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydrodrive of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Exhaust system check
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a distributing box
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. The thermostat of the air filter (carburettor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. System of catching of steams of gasoline
   2.24. System check рециркуляции
   2.25. Air заслонка the carburettor
   2.26. A zolotnik of system of ventilation картера
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of backlashes of valves
   2.30. Idling turns (carburettor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, бегунок and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a distributing box
   2.43. Oil replacement in a back (forward) reducer
   2.44. Backlashes in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


2.44. Backlashes in valves on the engine 1FZ-FE

Check and adjustment

Check and adjustment of backlashes in valves on the engine 1FZ-FE spend through each 96000 km, or every 4 year.


The prevention

Valves on this engine are regulated by selection of washers for a thickness, the special adaptation for отжатия pushers therefore is required.


For adjustment of valves of 6th cylinder it is required to remove cam-shafts. Therefore preliminary with special carefulness check up backlashes in these valves.

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Turn out candles (subsection 2.28 see), uncover heads of cylinders and establish the piston of 1st cylinder in ВМТ a compression step.
3. Measure a backlash between a cam of a cam-shaft and a pusher in the specified valves, writing down each result.
4. At check of backlashes щуп the given thickness should pass with small effort.
5. Turn коленвал on 1 turn rather ВМТ a compression step in 1st cylinder and measure backlashes in the valves specified in illustrations.
6. Having measured backlashes, turn коленвал so that the cam of a cam-shaft of the first adjustable valve has been turned upwards.
7. Wring out a pusher and get an adjusting washer. For this purpose establish the adaptation so that the long jaw of pincers of the adaptation grasped the bottom inflow under a pusher, and short rested against the top edge of the pusher. Compress pincers, push a small emphasis of the adaptation (or fasten a hook on handles of pincers), having fixed a pusher.
8. Clean pincers. Keeping a pusher, get an adjusting washer a screw-driver (a photo at the left) or magnetic tweezers (a photo on the right).
9. Measure by a micrometer a thickness of the removed adjusting washer.
10. Define a thickness of a remote lining at which the backlash in the valve will correspond to the standard:
N=Т + (А-V),
Т – a thickness of a removed adjusting washer,
And – a measured backlash,
N – a thickness of a new adjusting washer,
V – a demanded backlash (subsection 2.2 see).
11. The manufacturer in spare parts delivers adjusting washers of 17 dimensional groups. Pick up a washer so that the thickness of an established adjusting washer was as it is possible more close to settlement. It is possible to rearrange also the washer approaching on a thickness which have been removed from a pusher of other valve the backlash in which demands adjustment. It reduces number of got washers.
12. Wring out a pusher (see above) and establish a new adjusting washer.
13. Repeat procedure for other washers with which it is necessary to replace. Establish all removed details upside-down.

The table of dimensional groups of adjusting washers

1
2.500
2
2.550
3
2.600
4
2.650
5
2.700
6
2.750
7
2.800
8
2.850
9
2.900
10
2.950
11
3.000
12
3.050
13
3.100
14
3.150
15
3.200
16
3.250

17

3.300