Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation

Toyota Land Cruiser
+ 1. The maintenance instruction
- 2. Maintenance service
   2.1. Additional maintenance service
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance service terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tyres and pressure in tyres
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydrodrive of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Exhaust system check
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a distributing box
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. The thermostat of the air filter (carburettor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. System of catching of steams of gasoline
   2.24. System check рециркуляции
   2.25. Air заслонка the carburettor
   2.26. A zolotnik of system of ventilation картера
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of backlashes of valves
   2.30. Idling turns (carburettor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, бегунок and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a distributing box
   2.43. Oil replacement in a back (forward) reducer
   2.44. Backlashes in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes

2.38. Care of cooling system

Arrangement of a drain stopper of a cooling liquid

1. A drain stopper of the block of cylinders (all cars)

2. A drain stopper of a radiator on cars of late release

3. A drain stopper of a radiator on cars of early release

The prevention

Works are carried out on the cold engine at observance of safety measures (antifreeze is poisonous).

Replacement of a liquid and washing

1. Substitute a vessel under a drain stopper of a radiator.
2. Two flat-nose pliers turn away a drain stopper and a stopper of a mouth of a radiator (press and turn against часосой arrows). Merge a liquid. Then turn away a stopper and merge a liquid from the block of cylinders (if the liquid does not pour down, punch a screw-driver a rust in a drain aperture).
3. Check up and if necessary replace the damaged hoses of system of cooling.
4. Wash out a radiator a stream at its finest (deletes only a deposit), if necessary wash out a special washing-up liquid (deletes rust stratifications). If to wash out a radiator it is not possible, or if there are appreciable damages and a leak, remove a radiator and hand over in repair.
5. Disconnect a tank hose, merge a liquid, wash out a tank and dress a hose.
6. Tighten both drain stoppers.
7. Translate рычажок a heater in position maximum теплоотдачи.
8. Fill in a liquid (in the ratio 50/50 waters and antifreeze) to the bottom mark of a tank.
9. Without closing a stopper a radiator, warm up the engine before thermostat opening (it is felt on heating of the top hose).
10. Stop the engine and after cooling fill in a liquid to mouth edge, having pressed on a hose, remove air then turn a stopper.
11. Start the engine and be convinced of absence of a leak.