Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
- 2. Maintenance service
   2.1. Additional maintenance service
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance service terms
   - 2.5. Check of level of liquids
      2.5.1. Oil level in the engine
      2.5.2. A cooling liquid
      2.5.3. A liquid of a washer of a windscreen
      2.5.4. Electrolit of the storage battery
      2.5.5. A liquid of a hydrodrive of brakes and coupling
   2.6. Check of a condition of tyres and pressure in tyres
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydrodrive of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Exhaust system check
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a distributing box
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. The thermostat of the air filter (carburettor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. System of catching of steams of gasoline
   2.24. System check рециркуляции
   2.25. Air заслонка the carburettor
   2.26. A zolotnik of system of ventilation картера
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of backlashes of valves
   2.30. Idling turns (carburettor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, бегунок and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a distributing box
   2.43. Oil replacement in a back (forward) reducer
   2.44. Backlashes in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


2.5.1. Oil level in the engine
THE GENERAL DATA

Щуп маслоуказателя (engines 2F and 3F-E)

Щуп маслоуказателя (1) on engines 2F and 3F-E it is located on the right side.

Щуп маслоуказателя (engines 1ZF-FE)

Щуп маслоуказателя (it is specified by an arrow) on engines 1ZF-FE it is located on the left side.

Check of level of oil – the important preventive measure of operations of maintenance service. If oil level constantly goes down, the reason are an oil leak through the damaged epiploon, the weakened connections, or through piston rings or directing plugs of valves. If oil gets a dairy shade or in oil water drops tightness of a lining of a head of cylinders is broken are observed. It specifies all in necessity of immediate check of the engine. It is necessary to check an oil condition regularly also. Each time during check of level of oil before wiping щуп, clamp щуп two fingers and spend on it upwards. If it is visible that between fingers and щупом the rests of a dirt or small metal particles it is necessary to replace oil jam.

PERFORMANCE ORDER
1. Check up oil level щупом which is inserted into a branch pipe of the oil pallet of the engine.
2. Check oil level on the cold idle engine, or after nearby 15 minutes from the moment of its stop. If check of level of oil to make right after trips some part of oil remains in the top part of the engine and results of check will be erroneous.
3. Get control щуп from a tube and wipe its pure rag or a paper napkin. Insert pure щуп back into a tube and again get. Check up level on an oil film.
4. Oil level should is between risks L and F control щупа. Otherwise oil add (the quantity of oil corresponding to change of level from mark L to mark F, makes nearby 1л).
5. If oil level is above mark F, it will lead замасливанию candles, oil leak, or to epiploon failure.
6. To add oil, turn out a mouth stopper (it is specified стелкой) on a cover of a head of cylinders.